[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: gEDA-dev: Printing from PCB

To: geda-dev-at-NOSPAMmoria_dot_seul_dot_org
Subject: Re: gEDA-dev: Printing from PCB
From: DJ Delorie <dj-at-NOSPAMdelorie_dot_com>
Date: Wed, 29 Nov 2006 12:03:52 -0500
Delivery-Date: Wed, 29 Nov 2006 12:03:55 -0500
In-reply-to: <1164819268.5459.34.camel@pcjc2lap> (message from Peter Cliftonon Wed, 29 Nov 2006 16:54:28 +0000)
List-Archive: <http://www.seul.org/pipermail/geda-dev>
List-Help: <mailto:geda-dev-request@moria.seul.org?subject=help>
List-Id: gEDA developer mailing list <geda-dev.moria.seul.org>
List-Post: <mailto:geda-dev@moria.seul.org>
List-Subscribe: <http://www.seul.org/cgi-bin/mailman/listinfo/geda-dev>,<mailto:geda-dev-request@moria.seul.org?subject=subscribe>
List-Unsubscribe: <http://www.seul.org/cgi-bin/mailman/listinfo/geda-dev>,<mailto:geda-dev-request@moria.seul.org?subject=unsubscribe>
References: <1164805006.20919.5.camel@pcjc2lap><1164807334.25520.3.camel@pcjc2lap><200611291540.kATFenHp009199@envy.delorie.com><456DB591.6000302@mcmahill.net><200611291635.kATGZH04010841@envy.delorie.com><1164819268.5459.34.camel@pcjc2lap>
Reply-To: gEDA developer mailing list <geda-dev-at-NOSPAMmoria_dot_seul_dot_org>
Sender: geda-dev-bounces-at-NOSPAMmoria_dot_seul_dot_org


> It occurs to me that this is the same mirroring needed for toner
> transfer.. Do you have to do similar?

I just did a board[*] that uses toner transfer to etch the solder side
of a board I designed from the top.  It took a few minutes for me to
figure out whether I wanted it mirrored or not when I printed it.  The
answer was "not".  What I end up doing is disabling "auto mirror" and
exporting twice, once for each mirroring type.  Then I have lots of
pages to choose from.

[*] http://www.delorie.com/pcb/r8c-1b-adapter/


_______________________________________________
geda-dev mailing list
geda-dev@moria.seul.org
http://www.seul.org/cgi-bin/mailman/listinfo/geda-dev

Follow-Ups:
- Re: gEDA-dev: Printing from PCB
  - From: Peter Clifton
- Re: gEDA-dev: Printing from PCB
  - From: John Griessen

References:
- gEDA-dev: Printing from PCB
  - From: Peter Clifton
- Re: gEDA-dev: Printing from PCB
  - From: Peter Clifton
- Re: gEDA-dev: Printing from PCB
  - From: DJ Delorie
- Re: gEDA-dev: Printing from PCB
  - From: Dan McMahill
- Re: gEDA-dev: Printing from PCB
  - From: DJ Delorie
- Re: gEDA-dev: Printing from PCB
  - From: Peter Clifton

Prev by Date: Re: gEDA-dev: Printing from PCB
Next by Date: Re: gEDA-dev: Printing from PCB
Prev by thread: Re: gEDA-dev: Printing from PCB
Next by thread: Re: gEDA-dev: Printing from PCB
Index(es):
- Date
- Thread